Denso Direct Fit Oxygen Sensor DOX-2035

More Views

Denso Direct Fit Oxygen Sensor DOX-2035
Excl. Tax: £38.87 Incl. Tax: £46.64

Availability: Despatches in 1 - 2 business days, subject to availability

Denso Oxygen Sensor DOX-2035 Denso Direct Fit Oxygen Sensor (Lambda Sensor) part number DOX-2035

OR
Description

Details

Denso Direct Fit Oxygen Sensor DOX-2035

Primarily used in VOLKSWAGEN GROUP cars and typically replaces original equipment sensors including part number 1K0998262AB.

A common application for this sensor would be AUDI A6 (4B, C5) 2.4 (07/1998 - 01/2005).

Note that the figures in brackets denote the year and month of manufacture. Also fits other models, please use the 'lookup' on our homepage or on Denso's website. We strongly recommend cross referencing the original equipment (OE) sensor to the Denso aftermarket part in order to confirm suitability. See the CROSS REFERENCE tab for details. Contact us if you need help with this.

Refer to the ADDITIONAL INFORMATION tab for details of cable length and number of wires. Please visit the Denso Aftermarket website if you wish to identify suitable parts by vehicle registration (VRM) lookup.

Denso Direct Fit Oxygen Sensors, sometimes referred to as Lambda or O2 sensors or probes, are designed to be a 'plug and go' replacement for Original Equipment (OE) or competitor brand Oxygen sensors. This means you do not have to perform any cutting and reconnecting of cables, or need to reuse the original sensor connector. The correct connector for your vehicle's wiring loom is already attached to the direct fit replacement sensor.

Flange fitting type sensors are supplied with a gasket if required and sensors with a threaded fitting are either pre greased at the factory or are supplied with a sachet of suitable grease.

Simply disconnect your existing sensor from the vehicle's wiring loom, this is usually located in the engine bay and, using a suitable tool such as a Laser Lambda sensor socket for M18 threaded sensors, or the correct sized socket for sensors with flange fitting, carefully remove the existing sensor. Using the same tool, install the new sensor core, taking care not to damage the cables or the sensor body, connect back into the wiring loom and you're good to go.

Note that some vehicles may require an ECU reset in order to recalibrate engine management systems for the new sensor, this usually entails disconnecting the battery for a number of hours, overnight is usually sufficient.

Additional Information

Additional Information

Manufacturer Denso
Cable Length [mm] 1690
Number of Poles 4
Quality OE
Thread Size M18x1.5
ArtNr DOX-2035
Number Of Wires 4
Seat Type Threaded With Gasket
Part Type Direct Fit Lambda Sensor
Cross Reference
Manufacturer Part Number
AUDI058906265
AUDI077906265K
AUDI077906265L
AUDI077906265R
AUDI078906265N
AUDI078906265P
AUDI078906265Q
AUDI078906265R
BOSCH0258006014
BOSCH0258006283
BOSCH0258006285
BOSCH0258006312
BOSCH0258006314
BOSCH0258006336
BOSCH0258006338
BOSCH0258006371
SEAT058906265
SEAT077906265K
SEAT077906265L
SEAT077906265R
SEAT078906265N
SEAT078906265P
SEAT078906265Q
SEAT078906265R
SKODA058906265
SKODA077906265K
SKODA077906265L
SKODA077906265R
SKODA078906265N
SKODA078906265P
SKODA078906265Q
SKODA078906265R
VOLKSWAGEN058906265
VOLKSWAGEN077906265K
VOLKSWAGEN077906265L
VOLKSWAGEN077906265R
VOLKSWAGEN078906265N
VOLKSWAGEN078906265P
VOLKSWAGEN078906265Q
VOLKSWAGEN078906265R
WALKER25024414
Related Products