Denso Universal fit Oxygen Sensor DOX-0114
Primarily used in AUDI cars and typically replaces original equipment sensors including part number 030906265BH.
A common application for this sensor would be FORD KA (RB_) 1.3 i (199609 - 200811).
Note that the figures in brackets denote the year and month of manufacture. Also fits other models, please use the 'lookup' on our homepage or on Denso's website. We strongly recommend cross referencing the original equipment (OE) sensor to the Denso aftermarket part in order to confirm suitability. See the CROSS REFERENCE tab for details. Contact us if you need help with this.
Please also refer to the ADDITIONAL INFORMATION tab for details of cable length and number of wires. Please visit the Denso Aftermarket website if you wish to identify suitable parts by vehicle registration (VRM) lookup.
Denso Universal Fit Lambda Sensors, sometimes referred to as universal Oxygen or O2 sensors or probes, require utilising your original sensor electrical connector. Universal sensors are supplied with an excess of cable which needs to be cut to a suitable size for your vehicle and the connector for your original sensor can then be carefully spliced to the new sensor's cables using the insulated crimp connectors supplied or by soldering if preferred.
Flange fitting type sensors are supplied with a gasket if required and sensors with a threaded fitting are either pre greased at the factory or are supplied with a sachet of suitable grease.
Simply disconnect your existing sensor from the vehicle's wiring loom, this is usually located in the engine bay and, using a suitable tool such as a Laser Lambda sensor socket for M18 threaded sensors and the correct sized socket for sensors with flange fitting, carefully remove the existing sensor. Using the same tool, install the new sensor core, taking care not to damage the cables or the sensor body, connect back into the wiring loom and you're good to go.
Note that some vehicles may require an ECU reset in order to recalibrate engine management systems for the new sensor, this usually entails disconnecting the battery for a number of hours, overnight is usually sufficient.
- Additional Information
Manufacturer Denso Cable Length [mm] 750 Number of Poles 4 Quality OE Thread Size M18x1.5 ArtNr DOX-0114 Number Of Wires 4 Seat Type Threaded With Gasket Part Type Lambda Sensor
- Cross Reference
Manufacturer Part Number AUDI 030906265BH AUDI 030906265CB BOSCH 0258986507 DENSO DOX-0301 DENSO DOX-1093 DENSO DOX-1314 DENSO DOX-1353 DENSO DOX-1359 DENSO DOX-1546 DENSO DOX-1572 DENSO DOX-1573 DENSO DOX-1574 DENSO DOX-1575 DENSO DOX-1576 DENSO DOX-1598 FIAT 46426389 FORD 93GB9F472DA FORD 95FB9F472CB FORD 96FB9F472CA FORD 1013764 FORD 6847908 FORD 7011190 FORD 7126155 HYUNDAI 3921023215 HYUNDAI 3921023216 MERCEDES-BENZ 0005406117 MERCEDES-BENZ 0005406217 MERCEDES-BENZ 0005409217 MERCEDES-BENZ 0015400417 MERCEDES-BENZ 0015402117 MITSUBISHI MD197852 MITSUBISHI MD339900 MITSUBISHI MD351752 MITSUBISHI MD362314 NISSAN 226A01F701 NISSAN 226A01F725 NISSAN 226901F700 NISSAN 226901F701 OPEL 855345 OPEL 855353 OPEL 855360 OPEL 855366 OPEL 855375 OPEL 855390 OPEL 855523 OPEL 855524 OPEL 9118698 OPEL 12597989 RENAULT 7700107434 RENAULT 7700107438 RENAULT 7700871544 SEAT 030906265BH SEAT 030906265CB SKODA 030906265BH SKODA 030906265CB TOYOTA 8946502040 TOYOTA 8946502050 TOYOTA 8946505020 VOLKSWAGEN 030906265BH VOLKSWAGEN 030906265CB VOLVO 3531075 VOLVO 36022250
- Related Products